Working near wood chippers is dangerous
Working near wood chippers is dangerous
The National Institute for Occupational Safety and Health (NIOSH) in Cincinnati has issued a special warning concerning the hazards of working near wood chippers. The dangerous tools can kill quickly, before the worker has a chance to react, NIOSH warns.
According to the Bureau of Labor Statistics (BLS) Census of Fatal Occupational Injuries (CFOI), 11 workers lost their lives during 1992 through 1997 while working near mobile wood chippers. In seven of the incidents, the victim was caught by the feed mechanism and pulled through the chipper knives. The victims in four of the incidents were struck by hoods (guards that cover the rotating chipper knives) that separated from the machines after being improperly opened or closed while knives were still rotating.
During 1998, NIOSH received two more reports of worker deaths from operating wood chippers. NIOSH says these incidents illustrate the two most common causes of fatal injury: being fed through the chipper knives or being struck by the chipper disc hood. The incidents were investigated as part of the NIOSH Fatality Assessment and Control Evaluation (FACE) program.
Self-feeding mobile wood chippers commonly used during tree-trimming operations consist of a feed mechanism, knives mounted on a rotating chipper disc or drum, and a power plant. Tree branches and the feed mechanism or chipper knives grab trunk sections fed manually into the machine’s infeed hopper. The chipper disc or drum rotating between 1,000 rpm and 2,000 rpm cuts and propels wood chips through the discharge spout usually into a chip truck. The housing containing the chipper disc or drum is sectioned and includes a removable hood that allows access to machine components for maintenance.
Workers feeding material into self-feeding wood chippers are at risk of being fed through the chipper knives if they reach or fall into the infeed hopper or become entangled in branches feeding into the machine.
In one example offered by NIOSH, a 28-year-old groundsman died after he was caught and pulled into a wood chipper. The victim and two co-workers, a foreman and a climber, were cleaning up limbs after pruning a tulip poplar behind a town house. The coworkers were behind the building gathering loose branches while the victim was in front operating the chipper. The coworkers began dragging brush to the chipper. As the climber approached the chipper, he saw the victim’s legs sticking out of the infeed hopper. Investigators concluded that the victim either fell or reached into the infeed hopper while feeding short branches. His hands were caught by the feed mechanism, which forced his head and upper torso into the chipper knives.
NIOSH also offers this example of the other type of hazard, in which the worker is struck by part of the equipment: A 46-year-old laborer at a municipal waste-management facility died after he was struck by the flying chipper disc hood from an operating brush chipper. He had been feeding material into a chipper that had been converted to a stationary machine.
He had shut off the chipper to remove jammed material, but he opened the hood before the chipper disc had stopped completely. The rotating disc hit the hood as he opened it and tore it loose from its hinges. The hood struck the victim in the head and chest. He died the next day without regaining consciousness. Investigation showed that the hood hinges had been damaged, which allowed excessive side movement as the hood was swung open.
Tips to avoid getting caught in chipper
To protect workers from being caught by the chipper feed mechanism, NIOSH offers these recommendations:
• Ensure that all safety devices and controls, such as emergency shut-off devices, are tested and verified to be functioning properly before the chipper is used.
• Make sure workers are trained in safe work procedures, including operating wood chipper safety devices and safety controls. These procedures should be based on the manufacturer’s recommendations for each machine.
• Require that at least two workers are in close contact with each other when operating the chipper.
• Ensure workers wear close-fitting clothing, gloves without cuffs, trousers without cuffs, and skid-resistant foot wear. Clothing should be kept tucked in.
• Ensure workers’ hands and feet remain outside the infeed hopper.
• Instruct workers to feed brush and limbs into the infeed hopper butt end first.
• Position workers feeding material at the side of the machine to allow quick operation of the emergency shut-off device and minimize risk of entanglement in branches. Because of differences among machines, the manufacturer’s operating manual should be consulted for guidance. Safe feeding of some disc-type chippers requires the worker to be on the right side.
• Ensure workers walk away once the feed mechanism has grabbed the material.
• Ensure workers lay short material on top of longer material that is feeding or use a longer branch to push it through the infeed hopper.
• Ensure workers load small raked-up material such as twigs and leaves directly into the chip truck or in trash cans or bags instead of feeding it into the chipper.
• Require workers to keep the area around the wood chipper free of tripping hazards.
• Require workers to wear hard hats, eye protection, and hearing protection.
• To protect workers against being struck by flying hoods covering chipper discs or drums, employers should take these steps:
— Make sure wood chippers are inspected each working day before start-up for defects such as broken or missing hood latches and pins or cracked and worn hinges. Broken, damaged, or missing machine components should be repaired or replaced before the machine is placed in service.
— Ensure that the hood covering the chipper knives is completely closed and latched, according to manufacturer’s recommendations, before starting the machine.
— Before processing material and unless the manufacturer recommends otherwise, run the machine at the lowest possible speed while workers listen for noise that might indicate broken or loose machine parts. If unusual noise is detected, shut down the machine immediately and have it evaluated by a competent person. If necessary, the machine should be repaired before being placed in service.
— Make sure all internal machine parts have come to a complete stop before the hood covering the chipper disc or drum is opened.
Subscribe Now for Access
You have reached your article limit for the month. We hope you found our articles both enjoyable and insightful. For information on new subscriptions, product trials, alternative billing arrangements or group and site discounts please call 800-688-2421. We look forward to having you as a long-term member of the Relias Media community.